Calling Upon LR shooters, Bart B KraigWY ect.

Bart B.

New member
Service Rifle shooters are getting 1/2moa or better (the winners) at 600yds w/A2 match sights? If that's true, how come the current NRA service rifle record shows only 15 out of 20 shots in the 6" X-ring at 600 yards; a score of 200-15X? Where do you get this stuff?

Nobody, ever, has shot any rifle twenty times slung up in prone with no artificial support into no worse than 3 inches at 600 yards. I watched a guy put them into 4 inches at 600 some years ago setting a record, but one shot was outside the 6" X ring for a score of 200-19X. The current USA match rifle bolt action record is 200-20X with two more in it and the 22-shot group was about 5 inches. It was shot with a 24 caliber cartridge as far as I know. While it's possible for a semiauto 22 caliber rifle to shoot under 3 inches at 600 yards tested in free recoil clamped in a machine rest, hand held against ones shoulder introduces a lot of variables and that's why the best groups on bullseye targets at 600 yards have been over 6 inches.

The best prone competitors hold their aiming area inside 4 inches at 600 yards and break most of their shots inside 3 inches. Whatever accuracy the rifle and ammo has adds to that along with inconsistancies in hold causing the rifle to not move exactly the same way each time the bullet going down the barrel. Which is why people with half MOA centerfire rifles and ammo typically shoot 1.5 MOA at range laying on their bellies; records are set when a lot of luck's on their side and the group's smaller.

Nobody I know of reloads ammo for their match grade semiatuo service rifles winning matches and setting records. It's been tried but never produced the scores new cases do. Nobody squares up service rifle bolt faces, as far as I know.

The US Army Rifle Team had some of the best semiauto 5.56 NATO match rifles but they never shot the consistantly high scores past 600 yards that 7.62 NATO ones did from Garands and M1A's. That's why they Army team got the NRA to classify the AR10 in .308 Win. as a service rifle, then they went out and won 1000-yard matches and set a record with it.
 
Last edited:

MrBorland

New member
Bart B. said:
Service Rifle shooters are getting 1/2moa or better (the winners) at 600yds w/A2 match sights?

I've got to give this one the hairy eyeball, too.

The x-ring on an SR target is just under 1.3 MOA, and putting 20 rounds into it at 200 yards with a good A2 Service Rifle while prone is some darned fine SR shooting. I doubt one would even be able to categorically claim that all master-lever SR shooters can do it consistently.

A match-grade iron-sighted A2 AR15 is a great tool for the game it's intended to play in, but even my (albeit limited) experience has shown me a good scoped bolt rifle is the way to go for longer range precision.
 

Bart B.

New member
Mr. Borland, to give a view of what your hairy eyeball may uncover is the NRA record for 200-yard service rifle slow fire on the reduced 600 yard target. Its X ring is 1.79" diameter and the record is 15 out of 20 shots in or touching it; 200-15X. The other 5 shot were out somewhere in the 10 ring so I think the composite 20-shot group's 2 inches or bigger.

Shawn McKenna, the guy on the Army Team who holds it, used to shoot matches with me when he was a young teenager, but got picked up by the US Army Team shortly after his enlistment. His rifle using the best handloads in new cases probably shot an inch or a little less at 200 yards.

If one learns the aiming precision difference between post front sights (service rifle) vs. aperture front sights (match rifle) they'll better understand why service rifle groups on paper are larger making their scores lower. Light direction and amount will change the LOF angle with posts for a given sight setting but none with an aperture.
 
Last edited:

MrBorland

New member
Sounds like my hairy eyeball was justified, Bart.

I just looked over my notes, and the best I've done with my A2 on a 300-yard reduced 600y target (MR-63) was an 8x. Nearly twice that many seems like some mighty fine shooting indeed.

I chose the 200-yard SR x-ring in response to a challenge by Dick Whitting on the National Match forum. I think he chose those conditions because cleaning this x-ring is tough, but do-able. I've not yet cleaned it, but shot a number of 19xs, so I see it as a good challenge and motivation. Cleaning it with my scoped .260 bolt rifle ought to be easy in comparison.
 

edward hogan

New member
Thanks for your time and effort involved in posting the reply which I quoted entirely below....


My point was and remains the .223rem is as "accurate" or more than the .308win at the 500-600yd distances H-KFan stated he wanted to begin shooting. Maybe it is more the function of rifle selection, but your own second sentence gives some credence to the point that match .223 ammunition fired without support other than shooting coat and sling, from open sighted weapon is able to deliver "only 15 out of 20 shots in the 6" X-ring at 600 yards; a score of 200-15X?"

Would you allow that the potential for even finer precision results might occur with a scoped rifle on a varmint or highpower (longer barreled) upper? Probably wouldn't need be over 20" but most are at least for sight radius gains. The point of endorsing the AR-15 for starting point is its excellent capability and potential with much less recoil.

Somewhere in a Precision Shooting or Tactical Rifle magazine, I have an article by a SR competitor about a few modifications he made to his Dillon 550b which he used to load about 6000 rds of match and practice ammunition for he and his daughter every year. Lots of discussion, maybe archived, on the National Match board about use of progressive machines, including the Lee to load ammunition for SR comps.

Handloading match ammunition for .223 costs half or 1/3 as much as for .308. Buying it puts costs almost the same. Somebody else footing the bill, okay... If not, much less expensive to learn with the .223. If the wind blows the lighter bullets a bit more than 168/175s at 500/600yds, isn't that just more initiative to work at wind-calling skills?

I dunno about the "need" to true an AR-15 boltface. A Wylde chamber is not a true "match" chamber as it has tolerances to allow ammunition variation to assure consistent function. I have used a Starrett depth mic to gauge boltface variation, but not AR-15 bolts. Might be a quality control issue, but seems more concern for .476 and .533 boltface which have much greater area for variation to occur. Have seen lots of variation with Remington 700 bolts, none with Sako. Depends on the QC of the manufacturer, mostly, I guess.

As far as a Precision .223 with match ammo and high magnification scope, or even any scope of 6x or better, my premise is that the rifle will shoot with or better than a .308 at 500/600. To get the most of the learning experience, load the 75/77gr to magazine length and go shooting.

Seem to recall reading in Glen Zediker's book that David Tubb won the Wimbledon Cup with a .260rem chambered Knight's AR-25 in the mid-90s. The AR-10 precision rifle is exceptional, but why choose the .308win when can go .260rem or .260rem AI? There is also the 6mmXC which is a primo choice for longrange with even less recoil and very high BC bullets.

Unless one is bound by "rules for competition", why choose a .308win for anything in the precision or longrange shooting world?

Have seen Tubb's video of the One Mile Shot, and conditions are pretty damn windy there above Amarillo when filming. He shoots a 6.5/284 with a Leupold mk4 6.5-20x scope. Sure, Tubb is the great genius of the rifle, but mention this because he doesn't hamper himself with a .338 Lapua or .300rum to gain the velocity to cheat the wind, he goes lower recoil with highest BC 6.5 bullet.

If the purpose is longrange precision, why handicap yourself with more bullet weight and lower BC numbers, plus less velocity? Maybe the .223 is a bit of a handicap in the wind, but you're looking to LEARN The Wind. How better to learn?



=========================================================
Service Rifle shooters are getting 1/2moa or better (the winners) at 600yds w/A2 match sights? If that's true, how come the current NRA service rifle record shows only 15 out of 20 shots in the 6" X-ring at 600 yards; a score of 200-15X? Where do you get this stuff?

Nobody, ever, has shot any rifle twenty times slung up in prone with no artificial support into no worse than 3 inches at 600 yards. I watched a guy put them into 4 inches at 600 some years ago setting a record, but one shot was outside the 6" X ring for a score of 200-19X. The current USA match rifle bolt action record is 200-20X with two more in it and the 22-shot group was about 5 inches. It was shot with a 24 caliber cartridge as far as I know. While it's possible for a semiauto 22 caliber rifle to shoot under 3 inches at 600 yards tested in free recoil clamped in a machine rest, hand held against ones shoulder introduces a lot of variables and that's why the best groups on bullseye targets at 600 yards have been over 6 inches.

The best prone competitors hold their aiming area inside 4 inches at 600 yards and break most of their shots inside 3 inches. Whatever accuracy the rifle and ammo has adds to that along with inconsistancies in hold causing the rifle to not move exactly the same way each time the bullet going down the barrel. Which is why people with half MOA centerfire rifles and ammo typically shoot 1.5 MOA at range laying on their bellies; records are set when a lot of luck's on their side and the group's smaller.

Nobody I know of reloads ammo for their match grade semiatuo service rifles winning matches and setting records. It's been tried but never produced the scores new cases do. Nobody squares up service rifle bolt faces, as far as I know.

The US Army Rifle Team had some of the best semiauto 5.56 NATO match rifles but they never shot the consistantly high scores past 600 yards that 7.62 NATO ones did from Garands and M1A's. That's why they Army team got the NRA to classify the AR10 in .308 Win. as a service rifle, then they went out and won 1000-yard matches and set a record with it.
 

4runnerman

New member
Edward-223 is as accurate or more than a 308 at 600 yards?. Where in the world did that come from. Maybe on a perfectly calm day,moon just right,sun lined up just right with the planets:D. I have never heard something so silly.
This is why the 308 dominates FTR Class. Your choices are 223 or 308. Very,Very few choose the 223. Now while the 223 is very accurate it is so limited in wind conditions. I shoot both in FTR and I can tell you at 600 yards the 223 fails to even come close to the 308. A 60 gn bullet compared to a 175 gn bullet with a much Higher BC. There is no comparison.
 

Bart B.

New member
4runnerman, if the .223's barrel was a foot less than 600 yards long and held fairly still, it would probably shoot no worse than 1/4" groups that far away using a micro nuclear device in the case having enough energy to push the bullet out a barrel that long.
 

HKFan9

New member
My ARs are used for work / home defense they are set up as such, not long range precision guns.

I am not a novice shooter, and deal with firearms on a daily basis, but as I said it's more in defense type shooting not long range. I understand what you say about the .223 and I agree but it's not the setup I chose. I have been shooting .308s since I was 12 for deer hunting, flinching, specially with a 20lns rig is a non issue.


As I stated I was looking to get this rig up and going for distance, I have shot 500-800 yards before, but doing and truly understanding is a completely different ball game.
 

kraigwy

New member
I can tell you at 600 yards the 223 fails to even come close to the 308. A 60 gn bullet compared to a 175 gn bullet with a much Higher BC. There is no comparison.

I don't know of anyone who shoots 60 gr. 223s at 600. What you see is 80-90 gr bullets and they do quite well.

The 80 have about the same BC as the 175 gr bullets, and the 90s exceed the BC of 175s.

Don't you think there is a reason that 308 service rifles are rare as hen's teeth in Service Rifle High Power now days where the range is 200, 300, and 600 yards.
 

edward hogan

New member
In 2007, I attended a Service Rifle workshop which consisted of morning instruction and theory, and afternoon actual match. It was a Great Experience. The Double High Master who ran the event was a great guy who shot a plain-jane RRA NM rifle and stated one year he purposely didn't even clean the barrel fouling just to see if it mattered. It didn't. No maybes about it, the guy could shoot.

My eyes were opened that day to the capabilities of the AR-15. I have defined previously the factors that matter, and they apply to a bolt rifle or Armalite type: barrel length, twist, and heavy BTHP ammunition. 77gr is the heaviest can be assembled to keep magazine feed functions. Precision handloads offer greater versatility than factory match.

There is a famous quote about contempt prior to investigation...

If HK-Fan has an AR with a 20" barrel that will handle 75/77 gr bullets, and some 1:9 twist will, most won't; that rifle might be the ticket for eliminating all the variables (mostly) other than wind... Wind is really the only Variable the handloading rifleman cannot control.

Basically, you tune your rifle to deliver the best groups at 100/200 and prove the repeats and movement values of your scope's turrets, learn your load's ballistics, leaving learning to read mirage and wind. Going with the .223rem in a quality configuration, there is less gun-action to distract from holding steady follow-through or to disrupt position while shot is transiting the barrel.

Who has unlimited funds for this hobby? Personally, I would buy precision loading gear and maybe the new Sierra ballistics program and use their accuracy load with their 77matchking bullet and take control of all the variables I could influence.

As far as scopes go, have you "proved" your turret movements? Do they deliver that .1mrad rate of movement consistently? Do you need to dial past your value and return to it to unload springs? The 5-20x razor should be really amazing. Try it on your AR-15.
 

Bart B.

New member
Check the match scores from the NRA Nationals comparing match rifle to service rifle ones and see which ones are bigger. It's rare to see a .223 cartridge shot in the match rifles but most service rifles are now using it.

Checking a scope's adjustments for errors in the 1/4 click range requires something whose resolution is one-third that amount. So, it takes a rifle and ammo with at worst accuracy level in the sub 1/12th MOA range to measure the repeatability of a 1/4 MOA per click scope. Which is why I use a bench collimator to measure several scopes' repeatability and accuracy in their adjustments. One can be made at home that's accurate to 1/100th MOA. An optical collimator in the muzzle is a lot better than shooting bullets which typically has more human error introduced than anything else.
 

4runnerman

New member
Kraigwy- I don't doubt you for Service Rifles. However in FTR Class 308's domminate the 223 10 to one. My second to last Match in Grand Forks ( F Class Open) there was 3 people there shooting 600 yards with 55 gn bullets in 223.
They did place very good, but nothing compared to the 308's. Now I only shot FTR for one year and I can tell you to see a 223 out there was rare. If it would only be 300 yards and the ability to change rifles for the 600 yards there would be more. How ever what you shoot at 300,you also have to shoot at 600. No changing rifles mid match. I also have shot my 223 at 600 with a 75 gn bullet, Was good,but not as good as the 308 with a 155 or 175 g bullet. Never did try the 90 as you said-Maybe should give them a try too.
 

Jimro

New member
4runnerman,

A lot of F/TR matches go beyond 600, and the targets have smaller scoring rings than High Power. So factor in the longer distance and it becomes clear why the 308 is more popular than the 223, and it is for all the same reasons why 308 dominates Palma.

And honestly, on my belly, with a scope and a bipod, I'd choose 308 too. From a sling with irons? 223 every time.

Jimro
 

edward hogan

New member
We're friends here right?

I am sure Bart has forgotten 10x what little I know about shooting...

Resolution though, has nothing to do with "proving" scope turret movement values. Can do it using a collimator/boresighter like the Bushnell 74-3333, or on the paper with a box test shot at decent distance where/when wind is not a big factor. The collimator could show any movement errors. Just because the mfr says the reticle moves .25moa or .1mil don't mean it is true; might move, likely does with a bit different value. So, for real world results you prove your scope.

For sure I never mentioned any lightweight bullets in the .223. I still have some USA/FAE in 55gr, but 69gr bthp is the lightest I have ever loaded for AR use.

Want to learn the wind at 500/600, shoot a lighter bullet. Never heard of anyone shooting anything lighter than 69gr at 300yds, or even 200yds. Army Marksmanship Unit has won consistently using the 77gr at all ranges. Others vary their ammo according to distance. Of course, not applicable for H-K. Do remember seeing an officer stationed in Iraq/Afghanistan posting on the NM board that he really wished for a 20" rifle because the M4 barrel would not group/hit past 300/350yds. The 77gr match ammo is in regular mil inventory, being what is spec'd for the M249 squad mg; or was at the time.

Anyone shooting light bullets in a match of 200yds plus is very casual in their approach. At one time, I owned an LMT 14.5" upper and one barreled with a Noveske Aghan (I think) same oal stainless match barrel. Not really short enough for any advantage over a 20" rifle configured upper. Accurate, but limited, plus they beat-up my brass and were a bit more to control. Long gone, except I kept the LMT upper receiver and BCG and use them with a SR match barrel and free float tube.

I have 2 primo longrange ctgs to choose from in the 6mm/.22-250Ai or 6XC Long, and .260rem. Choosing a .308win for 1000yd shooting is like choosing a 5lb trigger with lots of creep and over-travel. Can be done, will test your ability to use it; but why select it if serious results are your goal? There is no award given for overcoming most handicaps on the way to excellence; just recognition of that excellence. What are the hot competitors shooting? It ain't the .308win unless rues require...
 

Bart B.

New member
Edward, I was the first person on this planet to shoot the 5.56mm M16 across the standard rifle couse, the National Match Course of 50 shots, in the USA. Only because I finished the 600 yard line on the first relay before anyone else. Happened in 1971 at the Nationals at Camp Perry. Our rifles had Redfield International rear sights giving about 1/3 MOA per click with the short sight radius.

The USN Team along with the Army and Marine Corps Teams all used Sierra's 52-gr. hollow point match bullet. That's all that anyone used for the first few years of 5.56 NATO rounds allowed in service rifle matches; both NRA and DCM. No other really accurate commercial bullets were available. Heavier bullets came around years later. Some folks reloading those bullets had them stick in the thick cardboard target backing used at some ranges' 600 yard lines. The pit crew pulled them out like darts from a dartboard.

Resolution? Who said anything about resolution in scopes. Do you think I use a collimator to measure resolution? Calculate approximate resolution using the Rayleigh criterion formulas.

Nobody can measure scope adjustment value repeatability to less than 1/4 MOA shooting groups unless the shoot their stuff no worse than 1/12th MOA and all group centers are equidistant and same angles from relative point of aim. Boxing a scope resolves adjustment repeatabiliy no smaller than the biggest group shot.

Hot competitors choose the .308 over the 22's when either are allowed for long range matches. NRA long range matches are shot at 800 through 1000 yards. Midrange is 500 and 600 yards.
 
Last edited:

4runnerman

New member
jimro-Yes you are correct on going past 600 yards, My point is even at 600 yards the 223 is out gunned by the 308. I have my 223 and it is probebly the most accurate rifle I have ( Barring the 6br) at ranges under 300 yards. After that the 308 takes over. The 223, like the 6PPC is very accurate but it is limited in it's range. Not sure is if there is a place where there is no wind ever?. Then the 223 would be great. I don't want to trash the 223, because it is my second most liked and shot rifle I own. I will never give it up. I don't shoot the 308 every weekend but I do the 223. It is just pure fun
 

HKFan9

New member
I like both rounds, but the rifle I bought at a deal came in .308 or .300 WM. I honestly bought the gun because I liked it, and I work in the industry for a master Kimber dealer and I am on their pro-staff... AKA I didn't pay close to retail for it.

I like controlled round feed admittedly, and the Mcmillian stock. When weighing my options... the Kimber is not a TRUE blue printed action, however they do hand finish the chamber, true the bolt face, and hand lap the lug, which was more than I would be getting on a rifle of similar price range (for me).

I chose .308 because I expected to shoot primarily UNDER 1000 yards, and I am not looking to get the tightest competition scores either. Basically just want to learn to hit a man or coyote sized target at varrying ranges, and just punch holes in paper targets or ring gongs. .300WM would have been more recoil, more ammo cost, and not needed at the ranges I intended it for.

I am saying my NEXT step will be 600 yards, not my goal. I have shot 5.56 AR's at 300-500-600 yards before, messing with different scopes reticles ect. Right now my AR's have 14.5'' or SHORTER barrels, so LR rigs they are not, however my BCM HSP Jack Carbine will shoot a pretty tight group when you slap a bipod and variable scope on it.:rolleyes:
 

Jimro

New member
4runnerman,

My point is even at 600 yards the 223 is out gunned by the 308. I have my 223 and it is probebly the most accurate rifle I have ( Barring the 6br) at ranges under 300 yards. After that the 308 takes over.

For target shooting I am having a hard time wrapping my mind around that statement. Ballistic energy and time of flight numbers may be used to make an "outgunned" argument, but they cannot be made to make a "more accurate" argument. I agree that the 308 is generally more accurate past 600, I have a very hard time thinking that the 223 is outgunned by the 308 past 300 when so many matches have shown otherwise.

Of course others have explained better than I why 223 dominates competitions out to 600 (especially service rifle) and why 308 dominates Palma and Long Range F/TR Class. http://riflemansjournal.blogspot.de/2012/03/cartridges-223-for-palma-competition.html

Jimro
 
Top