Brand new rem 700cdl 30-06 resized once fired brass from my rem 7600 pump, rcbs dies, rcbs shell holder, fl sized. Trimmed to length, deburred cleaned all lube from brass. Not primed, bolt closes extremely hard, have had brass in other calibers neck size where you can feel some pressure, but nothing like this. Not going to use this brass in this rifle, but can't figure out what is going on. This rifle is brand new, cleaned chamber, bore. Rifle has never been fired. Any ideas would help. Have brand new rem ammo, cycles and chambers fine.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
resized 30-06 brass chambers hard
- Thread starter flyboy14
- Start date
freakshow10mm
Moderator
How's your OAL?
Nine times out of ten the reason for this is improper set-up of the FL sizing die. Here is a quote from RCBS as proper FL die set up.
Step 5: Install the Sizer Die
Thread the sizer die into the press until the die touches the shell holder when the ram is at the top of the press stroke. Raise the press handle and turn the die down another one-eigth to one-quarter of a turn and set the large lock ring.
If you have not set up your FL die like this then you may not be bumping the shoulder back far enough. In fact you could actually be pushing the shoulder forward.
The other reason for this is that the expander ball is pulling the shoulder forward as you drag it through the neck. Make sure that the inside of the necks are clean and have a slight amount of lube. This will prevent the expander from stretching your brass.
Step 5: Install the Sizer Die
Thread the sizer die into the press until the die touches the shell holder when the ram is at the top of the press stroke. Raise the press handle and turn the die down another one-eigth to one-quarter of a turn and set the large lock ring.
If you have not set up your FL die like this then you may not be bumping the shoulder back far enough. In fact you could actually be pushing the shoulder forward.
The other reason for this is that the expander ball is pulling the shoulder forward as you drag it through the neck. Make sure that the inside of the necks are clean and have a slight amount of lube. This will prevent the expander from stretching your brass.
The squeak of the expander ball is right up there with fingernails on the chalk board.
TBS, I always lube inside the case neck. Back when, i used that sticky RCBS goop.
I guess i wasn't careful enough about cleaning the excess lube from the inside.
Well i had a KaBoom. had to pound the bolt open, brass came out de-primed and completely separated at the web. I was just shaken up, M-77R stayed together.
I initially thought i had overloaded the cartridge, and when i attempted to examine the rest of my loads, I couldn't pull the bullet. I tried vice grips above the press and pulled the lead apart or ripped the case out of the holder.
I then put the seating die in and found that i had to almost bend the press handle to crack the bullet loose. Over the 1 year post reloading this batch, The lube i failed to remove became a glue!
We learn by our, and others mistakes/experiences.
TBS, I always lube inside the case neck. Back when, i used that sticky RCBS goop.
I guess i wasn't careful enough about cleaning the excess lube from the inside.
Well i had a KaBoom. had to pound the bolt open, brass came out de-primed and completely separated at the web. I was just shaken up, M-77R stayed together.
I initially thought i had overloaded the cartridge, and when i attempted to examine the rest of my loads, I couldn't pull the bullet. I tried vice grips above the press and pulled the lead apart or ripped the case out of the holder.
I then put the seating die in and found that i had to almost bend the press handle to crack the bullet loose. Over the 1 year post reloading this batch, The lube i failed to remove became a glue!
We learn by our, and others mistakes/experiences.
TexasSeaRay
New member
The two best, consistent lubes I've used for rifle cartridge reloading have been one, the Lee lube, and two, a mixture of silica and graphite.
I like the Lee because I've never had a round contaminated, nor have I one get glued in like the preceeding poster experienced. I have had bullets glued in using (too much) of other brand lubes. Our unit armorer showed me what happens when a round gets glued in with some old M1 carbines that were destined for the scrap heap.
It ain't pretty and it's damned scary.
Loading rifle rounds is a very long, patient, drawn out process for me.
Some friends, who are also reloaders, lose patience with me when they're over at the house when I'm working up some rifle loads. They're more "come on, man, lube it, size it, fill it, seat it and put it in the box so we can go shoot it."
Jeff
I like the Lee because I've never had a round contaminated, nor have I one get glued in like the preceeding poster experienced. I have had bullets glued in using (too much) of other brand lubes. Our unit armorer showed me what happens when a round gets glued in with some old M1 carbines that were destined for the scrap heap.
It ain't pretty and it's damned scary.
Loading rifle rounds is a very long, patient, drawn out process for me.
Some friends, who are also reloaders, lose patience with me when they're over at the house when I'm working up some rifle loads. They're more "come on, man, lube it, size it, fill it, seat it and put it in the box so we can go shoot it."
Jeff
Thanks for all the info guys. Will have to wait until this weekend to fire the gun, with new ammo. Tried to chamber brass in my pump, and it chambered fine. Think I will try firing some new ammo out of both guns, and do a little measuring on the brass from both to try and compare it. Either way I appreciate all of the ideas.