I'm trying to install a barrel on a Savage rifle, no big deal I've done it several times. The thing that is different this time is I'm using an Accustock, the recoil lug isn't staked so it doesn't use the alignment notch on the action. I'm wondering if the parallel side recoil lug alignment tool PT&G sells for the Rem 700 will work to hold my recoil lug in place?
Recoil lug alignment tool?
- Thread starter taylorce1
- Start date
Savage and the Rem 700 will use the same recoil lug alignment jigs.
I use a Kleindorst jig made for tapered Holland's lugs (tapered are easier to pop free of the bedding).
You should consider replacing the factory lug when you go to the trouble of rebarreling. Factory lugs are stamped, not machined- and are never flat. They either need to be set up on a mill and machined flat- or replaced with a precision lug (which is much easier than milling one). Lug replacement is mandatory when I true actions, and strongly recommended at all other times. Well worth the $40.
I use a Kleindorst jig made for tapered Holland's lugs (tapered are easier to pop free of the bedding).
You should consider replacing the factory lug when you go to the trouble of rebarreling. Factory lugs are stamped, not machined- and are never flat. They either need to be set up on a mill and machined flat- or replaced with a precision lug (which is much easier than milling one). Lug replacement is mandatory when I true actions, and strongly recommended at all other times. Well worth the $40.
Thanks, that's what I thought. The problem with the Accustock is I didn't find an aftermarket lug for it. The Accustock uses a parallel lug that is shorter than the standard tapered lug that the non Accustock Savage's. Also because of the Accustok's bedding block I can't use a thicker than factory lug.
FrankenMauser
New member
I had a tool 3-D printed for non-standard, tapered recoil lugs on two Marlin X7s (last-ditch Remlins).
The company printed it in the wrong orientation, making the shear lines align perfectly with stress points; but it still worked. (And it was my fault for not locking the print orientation how I wanted it.)
Rear action screw used for attachment, since I couldn't obtain another 1/4"-28 screw of appropriate length without buying 100+. (And the front screw was too short.)
The tool aligns via the screw hole and lower receiver rails.
Terrible picture that was auto-color-corrected and made even worse. But it's what I've got.
The company printed it in the wrong orientation, making the shear lines align perfectly with stress points; but it still worked. (And it was my fault for not locking the print orientation how I wanted it.)
Rear action screw used for attachment, since I couldn't obtain another 1/4"-28 screw of appropriate length without buying 100+. (And the front screw was too short.)
The tool aligns via the screw hole and lower receiver rails.
Terrible picture that was auto-color-corrected and made even worse. But it's what I've got.
Attachments
Here was what I was dealing with, I bought the rifle off of gunbroker and when I got it I could tell it didn't have the proper recoil lug. They listed it as having an Accustock rifle but I had my doubts, it went cheap enough I bought it anyway. As you can see someone did a poor job grinding the factory recoil lug down .
Not even close to the same dimensions as my factory lug.
They must have been scared to grind anymore on the recoil lug, so they decided to take a dremel to the stock. Bubba is alive and well.
This is how an unmolested Accustock should look.
Here it is all test fitted up.
I did tear it all back down so I could send it off for some more work. Bolt body, barrel, and recoil lug are all getting coated and the bolt handle is getting a new knob.
Not even close to the same dimensions as my factory lug.
They must have been scared to grind anymore on the recoil lug, so they decided to take a dremel to the stock. Bubba is alive and well.
This is how an unmolested Accustock should look.
Here it is all test fitted up.
I did tear it all back down so I could send it off for some more work. Bolt body, barrel, and recoil lug are all getting coated and the bolt handle is getting a new knob.