You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
loading Penn bullets
- Thread starter rebs
- Start date
NoSecondBest
New member
I've been loading 357 and 38spl bullets for going on fifty years. I have yet to have a problem using anyone's bullets when seated in the crimping groove. For the difference in capacity you describe and the load you're using, you won't have a problem. Simply use loads listed in loading manuals, not loads you scrounged off the internet from some "keyboard expert". You'll be just fine. The OAL for most bullets is so that they don't extend past the cylinder and interfere with the gun cycling. Penn sells millions of these bullets and knows what they're doing. They state on their site they're "magnum" capable.
I to have those bullets for use in 9mm (as I recall you can get different OD for different semi autos. 124 gr of in that area, too lazy to look .
I forget what the issue was but the answers back were a bit snarky, they did id seat right (maybe in the grove for 9mm?- been a while) not work right.
I think he makes good bullets but his mold like is off or tried to cover too many bases with it, something.
I adjusted as needed and fine but was careful.
I forget what the issue was but the answers back were a bit snarky, they did id seat right (maybe in the grove for 9mm?- been a while) not work right.
I think he makes good bullets but his mold like is off or tried to cover too many bases with it, something.
I adjusted as needed and fine but was careful.
g.willikers
New member
Do you have an essential chronograph for working up loads?
Adjust powder load and bullet depth as needed for the results you want.
Hard to do without a chronograph just by guesstimates and heresay.
Adjust powder load and bullet depth as needed for the results you want.
Hard to do without a chronograph just by guesstimates and heresay.
g.willikers
New member
It's obvious that folks were successfully reloading long before the chronograph became available.
And there's not always a clear relation between velocity and pressure.
But until something better comes along, using a chronograph can help address the kinds of questions like yours.
The load data from the manufacturers' web sites and the various reloading manuals are usually very dependable - up until they aren't.
Like seating bullets deeper, for example.
And there's not always a clear relation between velocity and pressure.
But until something better comes along, using a chronograph can help address the kinds of questions like yours.
The load data from the manufacturers' web sites and the various reloading manuals are usually very dependable - up until they aren't.
Like seating bullets deeper, for example.
AGreed, Chnros were a million buck when I stared and if I rmemer you had rp replace screens.
Did ok, better stuff now and I do have one.
I don't use it a lot but it comes out and good to have when I do need it.
It also has an honorable ding on the front where I barely missed killing it at some point.
1/8 lower and take out the eye.
I was careful, now I am REALLY careful.
When I was riding motorcycle, there are those who have going down and those who are going to (and yes I went down fairly early and to this day not a clue why it did it, slow easy turn in the rain and no throttle, flipped up and over, werid)
With Chronographs there are those who have shot one and those who are going to. I shot mine and got away with it. Not too many can say that!
Did ok, better stuff now and I do have one.
I don't use it a lot but it comes out and good to have when I do need it.
It also has an honorable ding on the front where I barely missed killing it at some point.
1/8 lower and take out the eye.
I was careful, now I am REALLY careful.
When I was riding motorcycle, there are those who have going down and those who are going to (and yes I went down fairly early and to this day not a clue why it did it, slow easy turn in the rain and no throttle, flipped up and over, werid)
With Chronographs there are those who have shot one and those who are going to. I shot mine and got away with it. Not too many can say that!
g.willikers
New member
I winged mine pretty good, too.
But it still works.
The worst one I've seen killed was when a friend let his rifle droop just as he pulled the trigger.
He asked me to watch so he didn't do that.
I did for awhile until I got bored with him fiddling with the scope and momentarily looked away.
A 30-06 at close range is a helleva thing.
But it still works.
The worst one I've seen killed was when a friend let his rifle droop just as he pulled the trigger.
He asked me to watch so he didn't do that.
I did for awhile until I got bored with him fiddling with the scope and momentarily looked away.
A 30-06 at close range is a helleva thing.
Last edited: