Search results

i have been reading about doing a trigger job on the sig p238 but i havent found any thing too useful about it. i have read something about the leaf springs need straightened on one side and do this and polish that. has any one here done a trigger job on this pistol? what tools will i need? will...

i have recently began learning how to smith, and was asked by a friend to find a part for a s&w 41 mag revolver. he isnt sure what model it is and i have very very very little knowledge of revolvers, and the parts that make them work. after searching on line i could only find 2 models in that...

i was looking at a butt plate/pad for a k 31 bullpup i am making. i hadnt thought about this point until today and it is going to be finished very soon so this dilemma needs resolved. i wasnt sure about what to use and was thinking of using a spare plate i had for a winchester 94 pre 64 the...

i am making a stock for a swiss k31 and am getting a little more than i can chew. i was planing on using a 2 3/4" bolt for the front mounting bolt but this will get in the way of the trigger rod for my bullpup stock. can i shorten this bolt to a 1 3/4" and not compromise the integrity of the...

i am building a bull pup stock for a k31 YES I KNOW!!!!! why would i do it ??? to make it simple i plan to use a scout mount to eliminate the off center clamp on mount and the only way i can do that is by building a bull pup to shorten the eye relief. i also am learning a lot about wood...

i am working on a stock for a swiss k31 7.5x55. i was looking at the action the other day and noticed the i could work the wood an set in the major components of the action and still keep the barrel a hairs breath off of the wood without cutting a barrel channel. how deep does it have to be...

i have seen them carry glock 21,19 and have seen them carry a sigma 40 what is the most common issued sidearm?

i have been trying to trap yotes here in the tooele desert, its not going well at the moment i am laid off and strapped for cash i really could use a few yotes there is a 20$ bounty on them that would help loosen the belt a little. that being said what is a good make at home bait for yotes? i...

If I were a hunter, which I am not, I would go with a heavy barreled .223 (twist rate round 7 or 8:1), and have the chamber opened up for the 22-250AI. I would reload with one of the heavier bullets (80gr to 95gr). Any coyote I could see, would be my. __________________ READY on the...

i have benn TRYING to trap these buggers for some time know at first very unsuccessfully with no clue where to start. then i had a good idea how to go about it and still very unsuccessful. now i think im doing 80% of it right with my location distance between traps using the right equipment...

i gave up on the iron sights and decided to use a scoped rifle for coyote hunting the only rifle i can scope is a sav 99e in a .243 i dont shoot smaller rounds than my 7.62x39 what should i expect out of this rifle and just how much drop am i looking at if i am shooting 200yrds with a rem...

i inherited a win 94 30-30 pre 64 but the gate is missing where could i get the parts for it what parts are needed and how hard is it to put in i saw them on Winchester bobs site but he never picks up the phone i called for a week but no reply or email yet it loads and shoots fine with out it...

i saw a rubber limb-saver attachment that you put on your barrel to reduce vibration in you barrel but am not sure if i buy into the idea i though that vibration is necessary for an accurate barrel which is why they are often free floated has any one actually tried these and what did it do with...

i am making a custom stock and am planing to paint it i want to paint the barrel so i was thinking about using tape to cover it and paint over the tape will tape adhesive hurt the metal in any way if it is left on for long periods of time (months - years)???? is there a way to paint the berral...

i am building a stock for my k31 this month and i am looking for sling mount similar to the k31 or old military rifles the one that holds at the butt stock. the little bar with a screw at each end and it sits flush with the stock and the wood under it is cut out to make room for the sling what...

i was offered a trade for my 1959 winchester 94 30-30 mine is in great shape there is some blueing loss but not bad about 80-85% and a fine stock the trade is for a winchester model 70 ultimate shadow 300 shortmag with a simons 3-9 what is the moa trigger assembly i dont know any thing about...

i saw the video of the school board shooting today i watched it a few times in the 1950s would that have happened? maybe but i doubt it would have been as drawn out as it was. in 1900 would that have happened? even less likely. in about 4 generations we have lost so much of our American spirit...

i saw a post on trading site for a RARE 99e series a for $1000.00 did they make a 99e series a worth that much my guess is 600 at the most i have read that the .243 is the second most valuable savage rifle beat out only be some thing like a 26-3000 (not sure of the round) i think mine is a 99e...

any type of game but no fish small and large all inclusive what are to top 10 in my own opinion coyote is on there some where or its very close

i have asked tis on another forum also but havent heard any 1 reason repeated it seems to most i ask it that it does some thing else does it help with the speed you can retract the bolt does it provide less friction allowing it to turn easier or is it to simply look good im just starting to...