I'am a hater from way back.
I bought a coyote tan Gen 4 from CDNN with a extra threaded barrel $589. Maybe with the removable backstraps I can get a grip I like.
I'am just looking for a proven battle pistol. Hope this works out.
I'am trying 6.5 Grendel and Creedmoor long range steel plate shooting. I shoot both off a bench with bipod and rear bag. They both have TImney Triggers. They both like to fire two or three rd bursts.
I removed oils from the triggers with gun scrubber. Tried other uppers with with Timney...
I noticed my scope was loose on my Savage 10. My EGW rail was loose from the receiver. No big deal but one screw was missing, Where might I find some tapered screws? They are only 1/4 inch long.
A week ago I put a shockwave pistol in a compartment inside my SUV. The gun is in a scabbard with just the grip sticking out. I checked it yesterday and signs of rust already covering barrel. I was thinking being parkerized would help. I was thinking oily gun sock next. Any better ideas?
Every ASC mag 10 or 20 fails to feed if you load over 4 rds. The round loads short of battery and the bolt stops clear of rd. Drop mag, pull sticking charging handle back and tilt rifle upwards and rd comes out of chamber and falls out of magwell.
Only happens on over 4 rds in mag. When you...
I own a Dpms LR 308. I recently put a complete Aero 6.5 Creedmore upper on my lower. The Creedmore is an improvement in accuracy and I'am very happy with it.
Issue is I have a nice 308 upper sitting in a box with a nice 4X12 Vortex Scope. If I could find a stripped 308 lower, I thought of...
The only reasonable new stuff I've found is Hornady for $37 for 50. Are Nosler and Norma worth the extra coin? How much accuracy will I be missing out on?
For now I will re reloading my spent factory Federal and Hornady cases
I'am debating. It will be a range toy shot off a bench, maybe suppressed as well.
I have a M1A 22 inch I'am suppressing,DPMS LR308 and acouple scout rifles in 16 inch.
Help me make up my mind.
Thanks
I loaded some trimmed PPU brass at starting charge. Coal was 3.060. That's what printed coal was with a 168gr bullet. Before crimping I tried chambering a round in my K31. I couldn't get a round to full battery until 2.940. I could see marks on the shoulder of the Hornady HPBT keeping the bolt...
I finally pulled out my K31 and decied to sporterize it somewhat. I clamped on a St Marie scope mount and a cheap scope and went to the range. I was somewhat skeptical with the side mount scope. I put up six targets on a large piece of cardboard at 50yds. I was hoping to hit the cardboard...
Wouldn't cycle after three rounds. It would not eject a spent round. Then it became a single shot when I closed the bolt on the loaded mag. Then it would misfire and I would manually eject a loaded round with barely a nick on the primer. Rounds fired about 15.
Any help appreciated before...
I want one bad. I still cant make up my mind which one. Probably will end up suppressed and scoped. I'am leaning toward a loaded model but not sure on walnut vs syn stock.
I already have a CMP M1 Garand, DPMS LR308 and a couple of bolt 308 guns.
Any ideas welcome.
I have acquired 5 complete 223 and 300bo uppers from Primary Arms made by this company. 10.5 and 16 inch uppers. I paid $279 for each without BCG. They perform flawless and accurate. Fit and finish is awesome.
I tried to change a flashhider to support a can and twisted the barrel and broke the...
I have 3 AR pistols with sig arm braces. I want to go to SBR's
Can I build a SBR lower, engrave it and use it with all of my short barrel uppers legaly?
I have a trust and $200 wouldn't be bad for a couple of rifles.