Search results

I have a 12ga, Benelli Montefeltro with 26" barrel. I was considering getting an extra barrel and having it cut to 18" and threaded for choke tubes. 1) Stupid idea? 2) If no to the above question, any recommendations for a gunsmith?

I have a stamped steel trigger guard I need to have re-blued. Any recommendations?

5.3, 5.5, 5.6 & 5.7gr, 124gr FMJ from Precision Delta. The above loads seem to shoot 4-6inches lower at 10yds than 5.1-5.4gr of CFE-Pistol using the same bullet. Does that make any sense? The crimp was a little tighter with the BE-86 than with the CFE. Also, with the BE-86, I used CCI primers...

Specifically, to push a 124gr FMJ, Precision Delta bullet at 1100-1150 (5" barrel), and as accurate as possible at that velocity?

I tried some of my 9mm handloads using CFE Pistol powder. The fired cases were blackened. The loads were 5.1gr & 5.3gr, using a 124gr FMJ. OAL was 1.15. The way hotter factory Winchester NATO Q4318, came out shiny. A guess to the cause? Recommended loads using the 124gr FMJ and the CFE...

Has anyone used any of the above buckshot chokes? Any improvement in the pattern?

For my Benelli M4? If I was loading up on ammo right now, I would just be purchasing flight controlled BS, but I have hundreds of rounds of the regular stuff. As happy as I am with the accuracy of my M4 with slugs, I am not thrilled with BS at 50yds.

Can a .22 Hornet be loaded down to near .22 WMR levels and still be consistent and, depending on the rifle, accurate?

I believe this go around I will be getting into the local gun club. I thought I would celebrate with a nice, higher-end, walnut-stocked .22lr sporter. I can purchase the Sako new and can possibly find the other two still NIB or in LN condition for roughly the same $$. Which would you pick? Any...

Can you tell if the scope mount pictured below ( Conetrol without the finish ) will fit the above rifles?

Does anyone know for certain if the Conetrol H&KDT mount will fit the above listed rifles? I did contact Conetrol and their answer was " I believe so". The problem is I haven't purchased the rifle yet and do not want to pay nearly $2000 for a rifle, $250 for the mount, only to find I can't...

Sig P210 Target. The original owner said he put about 200rds thru. He replaced the target grips with standard grips and included both in the sale. I can't wait to shoot it. I have been wanting one for a couple of years ETA: The pistol is in EXC/LN condition, I do not know what those spots...

Not counting the specialty manufacturers like Buffalo Bore. When I am talking hot, I am not talking blow up your gun hot, I am looking for the hottest within SAAMI or CIP specs.

I was looking at these https://www.opticsplanet.com/v/50028-leupold-standard-2-piece-mount.html If I do go that route will Med. rings be high enough for the scope to be out of the way of the bolt? Better suggestions?

Brand new gun The manual safety. It is fairly easy to engage but feels locked in place when trying to disengage, not stiff or binding but stuck. I believe if I used pliers it would snap off. I have to wiggle and play with it and it finally drops. Sending it back to S&W would be a pain, even...

Has anyone run these two head to head in multiple guns?

All-around use; rabbits, squirrels. doves and very, very informal clay pigeons. I want quality & walnut. I have a Benelli M4 so I am covered in the slug & buckshot department. I would like to keep the purchase under 1k I have considered finding a used, local Remington 1100, used S&W 1000, and a...

Does anyone know?

Show off your Benelli I have owned mine for nearly 4 years, have shot it very little but I love handling it. Just recently switched out the pistol grip stock for this field stock

Has anyone run some over the chrony?