Search results

9mm cases will not enter the Lee resizing die. What could be the trouble? Thanks

Your thoughts: Lymon ammo checker vs LE Wilson case gauge? Thanks

Your thoughts about this powder measure please. Thank you Alan

Looking for practical suggestions for a powder dispenser. Currently using the Lee Perfect Powder Measure. Not too happy. I am getting bits of powder all over my bench. I an using HS6. Thanks

Happy Thanksgiving. Now why would a manual (Lee Modern Reloading) NOT have info for the 556 round? The 223 is there but not 556. I know they are very similar but I read that there are small differences. Whats up with that? What am I missing? Thanks

As my title says, what is the best way to remove a Hogue slip on grip? Several years ago it was hard to install and now I want to remove it. Thanks Alan

I am having a problem reloading 9mm. It seems that my empty cartridges after resizing will fit the wilson case gauge correctly. After loading and crimping they also fit the gauge. BUT at this point the fall short of completely fittin in my barrel. I am stumped. Any suggestions will be...

I am reloading 40 S&W. Seems that too often the primers will not even begin to seat. The pocket seems too narrow. Can I fix this and what tool(s) would I need? Thanks Alan

Why would you use the universal depriming die and not the one that comes with die set? Thanks. Alan

I am reloading 40S&W using Lee's 4 die set. Can (or should) I seat the bullet and crimp with the seating die and then crimp again with the Factory Crimp die? Also how would I just seat the bullet (no crimp) with seating die and then crimp with FCD? Thanks.

Today I loaded 40 S&W cartridges. I have been reloading for a while. SO I decapped,& resized and checked the fit in case gauge. All was ok. Then after charging the case and seating the bullet and then crimping with Lee Factory Crimp Die the cartridge is way too tight (wont fit) for case gauge...

I am getting ready to use the bulge buster (my first time) on .40 S&W cartridges. Can I use the BB on a cartridge that is loaded and bullet is seated and crimped? Instructions seem to say yes, but I am just verifying that I understand it correctly. Don't need any problems. Thanks.

I am looking to buy a digital scale and would appreciate your comments and suggestions. I had a scale but it would not register 7gr. Too light. Thanks Lets NOT break the bank. :p

How can I tell if the FA hand seat primer is the new and current model? I see photos with the push down lever to insert shell holder in different places. One in front and one on the side. Also best place to buy??

Are there other powders that basically clone HS-6? I ask because when I look for data for a cast bullet, 180g there seems to be no mention of HS-6 powder. So if there are other powders that mimic the HS-6 I would use that data if they would be listed on data sheets. Thanks

The Lee hand priming tool is a piece of junk. Primers going in sideways every few tries. My old style Lee unit was flawless but this one is a piece of cr*p. Any suggestions as to which one to replace it with? Thanks

I have 2 lee presses and have been using Lee dies (set of 4). I am thinking of trying another brand of dies. Any recommendations are appreciated. Do any othe brands have the equivalent of Lee's Factory Crimp die? Thanks

The only sp primers I could get were the magnums. I have read to lower the load a smidge. Would that be below the starting load? I will be loading 9mm, 40S&W, and 45acp. What say you? Thanks

I am looking for some load data. I have Missouri Bullets 40S&W 180gr bullets that are coated in HiTec. I have HS-6 powder. I have seen some videos where they say with this coating you need to lower the load by 10%. Thanks

Anyone know if the 5.11 ready range bag can be locked? Seems here in neverland the gun must be in a locked case while transporting to range, etc. A locked bag seems to be ok. Thanks.